Search found 1187 matches

by tooley92
31 Dec 2019, 8:18pm
Forum: Bikes & Bits – Technical section
Topic: 135mm 9 speed rear hub
Replies: 31
Views: 1468

Re: 135mm 9 speed rear hub

fastpedaller wrote:But are those dustcaps available to purchase anywhere?


I have a couple of unused ones lurking if you need some.
by tooley92
2 Oct 2019, 2:39pm
Forum: Bikes & Bits – Technical section
Topic: Rims worn out. Worth re building anymore?
Replies: 28
Views: 886

Re: Rims worn out. Worth re building anymore?

rmurphy195 wrote:Hope hubs aren't exactly cheap or nasty, are they! Rebuild with new rims.


True, but sadly they still crack!

The loudest freehub known to man.
by tooley92
1 Oct 2019, 9:21pm
Forum: Bikes & Bits – Technical section
Topic: Rims worn out. Worth re building anymore?
Replies: 28
Views: 886

Re: Rims worn out. Worth re building anymore?

Hope hubs? For sure it would be worth replacing the rims, especially, as others have mentioned you can find identical rims or rims with an identical ERD so that you can reuse spokes. Just make sure you check the hub flanges very carefully for hairline cracks, some of the older Hope hubs are notorio...
by tooley92
30 Sep 2019, 10:10pm
Forum: Bikes & Bits – Technical section
Topic: Cartridge bearing is rough when pressed in, but fine when taken out
Replies: 22
Views: 869

Re: Cartridge bearing is rough when pressed in, but fine when taken out

I think the hard bit without the correct tool is supporting the cup squarely whilst you drive out the bearing
by tooley92
30 Sep 2019, 2:26pm
Forum: Bikes & Bits – Technical section
Topic: Cartridge bearing is rough when pressed in, but fine when taken out
Replies: 22
Views: 869

Re: Cartridge bearing is rough when pressed in, but fine when taken out

The BB is Hope with it's own Hope ceramic bearing in. Another problem is if you knock the bearings out of this, you're having to whack the center to do it, which is all very well if you're not planning on putting them back in again but you can't get at the outer ring to remove them, only to press t...
by tooley92
29 Sep 2019, 9:01pm
Forum: Bikes & Bits – Technical section
Topic: Cartridge bearing is rough when pressed in, but fine when taken out
Replies: 22
Views: 869

Re: Cartridge bearing is rough when pressed in, but fine when taken out

The BB is Hope with it's own Hope ceramic bearing in. Another problem is if you knock the bearings out of this, you're having to whack the center to do it, which is all very well if you're not planning on putting them back in again but you can't get at the outer ring to remove them, only to press t...
by tooley92
13 Sep 2019, 2:21pm
Forum: Bikes & Bits – Technical section
Topic: How Old is Your Trangia ..
Replies: 46
Views: 2175

Re: How Old is Your Trangia ..

I have a few, the oldest bought new in about 1987.

A true design classic.
by tooley92
3 Aug 2019, 9:25pm
Forum: Bikes & Bits – Technical section
Topic: Torque Wrench Set Recommendations
Replies: 23
Views: 1767

Re: Torque Wrench Set Recommendations

For smaller fasteners I have this one

https://www.sealey.co.uk/product/563720 ... calibrated

It comes with me to work when the calibration man comes to do the workshop ones!
by tooley92
28 Jul 2019, 9:43pm
Forum: Bikes & Bits – Technical section
Topic: Carradice Super C rackbag on a Tubus Logo - stable?
Replies: 17
Views: 2325

Re: Carradice Super C rackbag on a Tubus Logo - stable?

I sold my Tubus Logo for the same reason-great with panniers but not so good with a rack bag. Cargo is a much better fit with the Super C bag. Have you tried the Super C AND panniers on the Cargo? If so how fiddly was it getting them on? Good point! Normally either or for me - most of the time rack...
by tooley92
28 Jul 2019, 8:39pm
Forum: Bikes & Bits – Technical section
Topic: Carradice Super C rackbag on a Tubus Logo - stable?
Replies: 17
Views: 2325

Re: Carradice Super C rackbag on a Tubus Logo - stable?

I sold my Tubus Logo for the same reason-great with panniers but not so good with a rack bag. Cargo is a much better fit with the Super C bag.
by tooley92
16 Jun 2019, 9:07pm
Forum: Does anyone know … ?
Topic: Which new canti's for a Raleigh Randonneur.
Replies: 19
Views: 972

Re: Which new canti's for a Raleigh Randonneur.

What's wrong with the original ones?

If you've got narrow boss spacing they are one of the best brakes available, can be upgraded with holders for xtr style slot in pads.
by tooley92
21 Feb 2019, 2:29pm
Forum: Bikes & Bits – Technical section
Topic: before indexing....
Replies: 20
Views: 2010

Re: before indexing....

S2L wrote:Nice... shouldn't use Shimano cables on Campagnolo levers though... :wink:



Looks more like a brake cable!
by tooley92
18 Dec 2018, 2:20pm
Forum: Bikes & Bits – Technical section
Topic: Has Anyone (Actually) Seen a Ryde Sputnik Rim
Replies: 10
Views: 750

Re: Has Anyone (Actually) Seen a Ryde Sputnik Rim

Yep, I’ve a pair that Spa supplied earlier in the year.
by tooley92
29 Mar 2018, 7:53pm
Forum: Does anyone know … ?
Topic: what's going on with framebuilder steve goff?
Replies: 68
Views: 8142

Re: what's going on with framebuilder steve goff?

He's still alive & building!

I know he's got quite a bit on at the moment and is working through a waiting list - Steve is a great builder - keep onto him and you won't be disappointed when it's finished.

I'm prob going to order another one from him later on in the year.