Bent handlebars!!!

General cycling advice ( NOT technical ! )
Enso
Posts: 2
Joined: 9 Aug 2019, 3:22pm

Bent handlebars!!!

Postby Enso » 9 Aug 2019, 3:32pm

Hi all, looking for some advice if you can help....and contain your giggles!

Fell over on the kitchen floor in road shoes and landed on my bike bending the drop on the right side of the handlebars inward by about an inch... I've gone ahead and bent it back to very nearly it's original position so that you wouldn't really know to look at it....

Question is should I be concerned about the integrity of the bar after a drop from standing height and a bend back or just crack on and forget about it?

The bike is a Giant defy advanced 2 and I believe the bars are aluminium but I'm open to correction....

Vorpal
Moderator
Posts: 16937
Joined: 19 Jan 2009, 3:34pm
Location: Not there ;)

Re: Bent handlebars!!!

Postby Vorpal » 9 Aug 2019, 3:46pm

If they are aluminium, I would replace them. Bending them, and bending them back again will have introduced stresses that will eventually be a failure point. Cold bending aluminium tends to introduce micro cracks, anyway, so there is a good chance that there are cracks that you can't see.

Don't risk your steering for a £30 or £40 part.

If they are steel, it's probably okay, but I would disassemble them & check the joint around the clamp. Even if the bending occurred on the drop part, the clamp area is a stress riser, and the area could be damaged from the fall, and you haven't noticed.
“In some ways, it is easier to be a dissident, for then one is without responsibility.”
― Nelson Mandela, Long Walk to Freedom

User avatar
NUKe
Posts: 3652
Joined: 23 Apr 2007, 11:07pm
Location: Suffolk

Re: Bent handlebars!!!

Postby NUKe » 9 Aug 2019, 5:09pm

vorpal said it, it really not funny when bars strees fracture latter on. just replace them
NUKe
_____________________________________

User avatar
Spinners
Posts: 1329
Joined: 6 Dec 2008, 6:58pm
Location: Port Talbot

Re: Bent handlebars!!!

Postby Spinners » 9 Aug 2019, 5:36pm

That must have hurt?

If they're aluminium then, personally, I'd continue to ride them but I would definitely take a peek under the bar tape for signs of a crease or stress.
Cycling UK Life Member
PBP Ancien (2007)

Enso
Posts: 2
Joined: 9 Aug 2019, 3:22pm

Re: Bent handlebars!!!

Postby Enso » 9 Aug 2019, 6:02pm

Thanks for the thoughts.....

The bike is pretty new so in an ideal world if I swap the bars out I'd like to replace like for like, a quick search shows the contact sl d-fuse bars will cost me about £65..... Any other suggestions for suitable replacements?

gxaustin
Posts: 473
Joined: 23 Sep 2015, 12:07pm

Re: Bent handlebars!!!

Postby gxaustin » 15 Aug 2019, 12:28am

The bike is pretty new so in an ideal world if I swap the bars out I'd like to replace like for like, a quick search shows the contact sl d-fuse bars will cost me about £65..... Any other suggestions for suitable replacements?


I doubt your bars are special. Any bars should do as long as they have the width, drop and reach you want. Deda, FSA Omega are about £30. Ritchey - the list is endless.

Brucey
Posts: 34807
Joined: 4 Jan 2012, 6:25pm

Re: Bent handlebars!!!

Postby Brucey » 15 Aug 2019, 7:58am

aluminium handlebars are made in several distinct ways. The two most common (on modern road bike drops) are

a) cold formed (with the material in the softened condition) and then heat treated for strength
b) just cold formed

There are good bars of each sort and price is no indication of manufacturing method.

If the former sort the bars are very likely to be damaged by being bent and straightened, and may subsequently break with little or no warning (eg under the bar tape). If the latter sort, a modest bend and straighten will usually be tolerated, but even then you can't be 100% sure.

Thus if you are in any doubt you should change them.

cheers
-------------------------------------------------------------------------------
~~~~~~~~~~~~~~~~~~~~~~Brucey~~~~~~~~~~~~~~~~~~~~~~~~

9494arnold
Posts: 821
Joined: 21 Jan 2007, 3:13pm

Re: Bent handlebars!!!

Postby 9494arnold » 15 Aug 2019, 8:43am

I'd replace them.
It's no fun if they break during a ride. (It has happened to me fortunately at very low speed)
I also saw a mate drop his bike unloading it from his car, half way through the ride his Carbon Bars let go. Again fortunately he wasn't going quickly. :?
Imagine going downhill under braking and they let go. You might not live to tell the tale. :shock:
And I doubt if anyone who wears cleats is giggling. It's like being on sheet ice in the wrong underfoot conditions.

lescargo
Posts: 144
Joined: 27 Dec 2013, 11:51pm
Location: Tyneside

Re: Bent handlebars!!!

Postby lescargo » 16 Aug 2019, 2:53pm

As almost all above advise, change them.
Have pair used "ONE23" bars 42cm.w x 31.8 diam.
You can have these for postage cost.
If you want them pm. me your phone number.
At 77 I don't think I will be building any more bikes up!!

gregoryoftours
Posts: 997
Joined: 22 May 2011, 7:14pm

Re: Bent handlebars!!!

Postby gregoryoftours » 17 Aug 2019, 1:42am

An inch bend and back is a fair amount I'd say. How it happened is fairly irrelevant. The cost of replacing the bar will be less than that of getting new teeth. I certainly wouldn't take the risk.