Moulton TSR rear pivot
Re: Moulton TSR rear pivot
I suppose you're right about that, but it'll be many many times down the line before that is realistic .............. fingers crossed.
However, these are the third set in now for me. Bike brand new in March 2016 and has done less than 8,000miles.
That's two pairs of bushes worn, so that's one set per 4,000miles.
Considering that my Mercian has done 50,000miles since 1986 when I bought it ............. had it been a Moulton TSR, it would have consumed more than a dozen pairs.
However, these are the third set in now for me. Bike brand new in March 2016 and has done less than 8,000miles.
That's two pairs of bushes worn, so that's one set per 4,000miles.
Considering that my Mercian has done 50,000miles since 1986 when I bought it ............. had it been a Moulton TSR, it would have consumed more than a dozen pairs.
Mick F. Cornwall
Re: Moulton TSR rear pivot
I replaced my bushings a couple of years ago with the factory ones, and didn't think to examine the housing in any detail.
But, I'm now wondering, what's to stop one from fitting longer bushings, so as to increase the bearing surface and hence reduce wear? Are longer bushings available, and if so, are there any obstructions (other than the grease nipple) that would prevent them from being inserted? Or would longer bushings prevent lubrication from getting where it's needed?
But, I'm now wondering, what's to stop one from fitting longer bushings, so as to increase the bearing surface and hence reduce wear? Are longer bushings available, and if so, are there any obstructions (other than the grease nipple) that would prevent them from being inserted? Or would longer bushings prevent lubrication from getting where it's needed?
Re: Moulton TSR rear pivot
One thing to check next time, is to put the new bushes on the new spindle and feel the play and the freedom and how they slide back and forth.
Then, after fitting the bushes, you will find that the spindle goes in firmly and with zero play.
This will be because bronze bushes are softer and squishier than the rigid steel frame tube and therefore compress.
It has been suggested, and it's true I'm sure, that fitting new bushes and fitting a new - but slightly over-sized spindle - then parallel reaming to accurately suit the new spindle would be the best most Rolls Royce way of doing it.
............ but you'd need a non-standard spindle custom-made first.
Then, after fitting the bushes, you will find that the spindle goes in firmly and with zero play.
This will be because bronze bushes are softer and squishier than the rigid steel frame tube and therefore compress.
It has been suggested, and it's true I'm sure, that fitting new bushes and fitting a new - but slightly over-sized spindle - then parallel reaming to accurately suit the new spindle would be the best most Rolls Royce way of doing it.
............ but you'd need a non-standard spindle custom-made first.
Mick F. Cornwall
Re: Moulton TSR rear pivot
One thing I didn't say, was that this morning I fitted the new modified Simply Bearings bushes ............ at a few quid each ........... but fitted the old original spindle and the old original securing bolt and washers. Nowt wrong with the bolt and washers, and the spindle is hardly worn at all.
I still have the brand new spindle and bolt and washers, so all that's needed for a refurb, is modified Simply Bearings bushes.
https://simplybearings.co.uk/shop/p1205 ... _info.html
I bought a pack of two for £6.04 including VAT and free delivery.
I still have the brand new spindle and bolt and washers, so all that's needed for a refurb, is modified Simply Bearings bushes.
https://simplybearings.co.uk/shop/p1205 ... _info.html
I bought a pack of two for £6.04 including VAT and free delivery.
Mick F. Cornwall
Re: Moulton TSR rear pivot
Had a chat with my mate yesterday afternoon and asked him if his dad would be happy to modify more of these bushes. He said he'd be delighted.
So, I'm going to buy eight new bushes (four pairs) and they will see me ok for years and years.
One pair seems to last 4,000miles, so that'll be 16,000miles worth.
So, I'm going to buy eight new bushes (four pairs) and they will see me ok for years and years.
One pair seems to last 4,000miles, so that'll be 16,000miles worth.
Mick F. Cornwall
Re: Moulton TSR rear pivot
A bit late to the party I know, sorry. You've fitted grease nipples to this pivot, but have you thought about actually drilling through the pivot housing tube and oilite bush and then fitting those little oil reservoir things with a flip lid, so that you can have a drip feed of oil to the bush? They used to be common on steam engines and lathes.
- simonineaston
- Posts: 8063
- Joined: 9 May 2007, 1:06pm
- Location: ...at a cricket ground
Re: Moulton TSR rear pivot
whoa - steady, Fausto! - that could upset Mick's entire strategy...
S
(on the look out for Armageddon, on board a Brompton nano & ever-changing Moultons)
(on the look out for Armageddon, on board a Brompton nano & ever-changing Moultons)
Re: Moulton TSR rear pivot
Knowing what I know now about these pivots, it matters not what you do to lube the bushes as the pivot hardly moves.
Any grease will be too thin in the place where they wear.
I've proved it by removing them and rotating then 45degs and all play went. The only wear in one area and not all round.
Putting an oiler in wouldn't help at all as the thing doesn't rotate, just jiggles over a tiny arc.
Grease often with a grease gun is all that's needed ............ but they'll only last 4,000miles.
Terrible design, but cheap enough to replace so long as you don't buy a whole kit from Moulton. Mine is still on the original spindle and the original securing bolt as there's nothing wrong with either of them.
Just buy bushes from Simply Bearings and trim down the flange thickness. £6 a pair for 4,000miles of use.
The bushes are pre-oiled but are designed for rotation equipment, not for pivoting on a tiny arc.
Any grease will be too thin in the place where they wear.
I've proved it by removing them and rotating then 45degs and all play went. The only wear in one area and not all round.
Putting an oiler in wouldn't help at all as the thing doesn't rotate, just jiggles over a tiny arc.
Grease often with a grease gun is all that's needed ............ but they'll only last 4,000miles.
Terrible design, but cheap enough to replace so long as you don't buy a whole kit from Moulton. Mine is still on the original spindle and the original securing bolt as there's nothing wrong with either of them.
Just buy bushes from Simply Bearings and trim down the flange thickness. £6 a pair for 4,000miles of use.
The bushes are pre-oiled but are designed for rotation equipment, not for pivoting on a tiny arc.
Mick F. Cornwall
Re: Moulton TSR rear pivot
You'd probably be better off with hardened steel bushes for that job. But they would need to be kept well oiled to prevent rusting.
I suspect that the oilite bronze bushes aren't so much wearing but being spread slightly by the constant road chatter. Oil absorbent bronze is quite soft.
Anyway probably not worth it now you've got a stock of them.
I suspect that the oilite bronze bushes aren't so much wearing but being spread slightly by the constant road chatter. Oil absorbent bronze is quite soft.
Anyway probably not worth it now you've got a stock of them.
Cheers
J Bro
J Bro
Re: Moulton TSR rear pivot
Mick F wrote:Knowing what I know now about these pivots, it matters not what you do to lube the bushes as the pivot hardly moves.
Any grease will be too thin in the place where they wear.
I've proved it by removing them and rotating then 45degs and all play went. The only wear in one area and not all round.
Putting an oiler in wouldn't help at all as the thing doesn't rotate, just jiggles over a tiny arc.
Grease often with a grease gun is all that's needed ............ but they'll only last 4,000miles.
I obviously don't ride my Mk1 anything like as much as you do your TSR. I replaced the nylon bushes with oilite ones way back in the 80s and have not touched them since. No signs of any wear or play yet. I will have to take it apart to investigate the rubber squeaking, so I'll have a closer look then. Having said all that, my lockdown project carbon tube converted Mk1 will have a grease nipple fitted to the tube centre while it's still in pieces.
-
- Posts: 3563
- Joined: 5 Aug 2009, 7:22pm
Re: Moulton TSR rear pivot
fausto99 wrote:I obviously don't ride my Mk1 anything like as much as you do your TSR. I replaced the nylon bushes with oilite ones way back in the 80s and have not touched them since. No signs of any wear or play yet. I will have to take it apart to investigate the rubber squeaking, so I'll have a closer look then. Having said all that, my lockdown project carbon tube converted Mk1 will have a grease nipple fitted to the tube centre while it's still in pieces.
Smug face see my previous comment dated 18th May 2020 [ i.e. page 19 ]
Last edited by Graham on 19 Jul 2020, 9:52am, edited 1 time in total.
Reason: ref to page 19
Reason: ref to page 19
Re: Moulton TSR rear pivot
in the far mists of time I had a couple of Mk1 moultons and I couldn't understand why I couldn't get the swingarm spindles out. Nor could anyone else. I recently found out that the very earliest Mk1 moultons were fitted with bronze bushes, not plastic ones, which explains why they can seize up so completely, if neglected.
cheers
cheers
-------------------------------------------------------------------------------
~~~~~~~~~~~~~~~~~~~~~~Brucey~~~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~~~~~~~~~~~~~Brucey~~~~~~~~~~~~~~~~~~~~~~~~
Re: Moulton TSR rear pivot
Bought them the other day, and delivered this afternoon.Mick F wrote:Had a chat with my mate yesterday afternoon and asked him if his dad would be happy to modify more of these bushes. He said he'd be delighted.
So, I'm going to buy eight new bushes (four pairs) and they will see me ok for years and years.
One pair seems to last 4,000miles, so that'll be 16,000miles worth.
You can order "by the each" - or packs of five or ten.
Five would be pointless as they're used in pairs of course, so I bought a pack of ten.
Including Vat (free delivery) the bill came to £16.45 ........ that's £3.29 a pair for the five pairs.
I'll get all ten modified, keep maybe three pairs
If someone would like a couple of pairs, I can post them off at the cost price (plus postage) .............. but it may be a couple of weeks or more before I can get them trimmed down.
If nobody wants them, I'll have enough to keep my TSR going until I'm way past cycling age!
Mick F. Cornwall
- simonineaston
- Posts: 8063
- Joined: 9 May 2007, 1:06pm
- Location: ...at a cricket ground
Re: Moulton TSR rear pivot
I've just bought a ten year old TSR frame for a new project (Alfine hub...) so I'd be daft not buy a couple of pairs off of you, Mick!
S
(on the look out for Armageddon, on board a Brompton nano & ever-changing Moultons)
(on the look out for Armageddon, on board a Brompton nano & ever-changing Moultons)
Re: Moulton TSR rear pivot
The bushes in that frame have been replaced, probably less than 1000 miles ago.