New front mech needed

For discussions about bikes and equipment.
justinmg
Posts: 3
Joined: 24 Mar 2019, 12:33pm

New front mech needed

Postby justinmg » 22 Apr 2020, 8:58am

I am trying to refurbish an old bike.
The front mech trim screws are completely seized (even after a night under WD40) and I think it needs replacing.
Its for a 2x9 Sora setup and is marked FD5600. This part does not seem to be sold now. Can anyone suggest how to work out a replacement. It seems it was used as a past 105 item from an internet search, but this would be when they were 10sp??? Will any 9sp / 10sp 2x front work if the mount is OK?

Thanks
Justin
Image Attachments
IMG_1532.jpg

hamster
Posts: 3715
Joined: 2 Feb 2007, 12:42pm

Re: New front mech needed

Postby hamster » 22 Apr 2020, 9:32am

If it's 5600 series then it's 105.

Personally I'd have a look on ebay. There are usually plenty of new old stock front mechs available.

Brucey
Posts: 42167
Joined: 4 Jan 2012, 6:25pm

Re: New front mech needed

Postby Brucey » 22 Apr 2020, 10:31am

for a 9s transmission you may be better off with a 9s mech than a 10s one; in many (but not all) cases the 10s mechs are slightly narrower and this leads to increased rubbing tendencies with 9s chain running through them.

FD-3400, FD-5500, FD-6500 are all very similar in appearance to FD-5600 and (I think, do check) have similar capacities etc. FD-3500 is available in a dark finish if you prefer that. All use the same shift ratio, so ought to work fine with the shifter.

FDs (of this sort) don't wear out that often so are usually a reasonable used buy. Of current-ish/recent stuff that you might most easily buy new, FD-3500 or FD-2400 (8s) ought to be a reasonable bet.

cheers
-------------------------------------------------------------------------------
~~~~~~~~~~~~~~~~~~~~~~Brucey~~~~~~~~~~~~~~~~~~~~~~~~

User avatar
Chris Jeggo
Posts: 196
Joined: 3 Jul 2010, 9:44am
Location: Woking

Re: New front mech needed

Postby Chris Jeggo » 22 Apr 2020, 12:38pm

Have you tried PlusGas penetrating oil on the seized screws?

User avatar
Graham
Moderator
Posts: 6489
Joined: 14 Dec 2006, 8:48pm

Re: New front mech needed

Postby Graham » 22 Apr 2020, 1:12pm

Fuzzy memory time, but don't those limit screws have an unusual head-type. . . . one that is dead-easy to mangle using the usual type of screwdriver ?

I have vague recollections of knowledgeable persons recommending the purchase of this PROPER screwdriver, for just such an event . . . .

. . . or maybe it was just all imagined ( along with most of my waking consciousness ) . . .

User avatar
531colin
Posts: 13323
Joined: 4 Dec 2009, 6:56pm
Location: North Yorkshire

Re: New front mech needed

Postby 531colin » 22 Apr 2020, 3:41pm

Yeah, its a JIS (Japanese industry standard) cross-head screw which isn't quite either Posidrive or Phillips, but somewhere in between.
If the mech. is knackered anyway, I would take it off and warm it up a bit. More than a bit really; with a blowtorch, but nowhere near red heat.
The adjustment screws are set in a bit of plastic to stop them rattling loose and you will set fire to that plastic bit, but you just might be able to free off the screws with heat and penetrating oil.

bgnukem
Posts: 565
Joined: 20 Dec 2010, 5:21pm

Re: New front mech needed

Postby bgnukem » 22 Apr 2020, 6:21pm

Just small Philip screw heads, sometimes with a full-width slot permitting the use of a cross-head screwdriver.

pwa
Posts: 13649
Joined: 2 Oct 2011, 8:55pm

Re: New front mech needed

Postby pwa » 22 Apr 2020, 6:25pm

I generally find the screwdriver slips less on those screws if it is a well fitting slot screwdriver rather than a cross-pattern phillips /pozi.