no H and L on mech screws
no H and L on mech screws
I need to adjust the front mech but it is an elderly bike and has no H and L screws on mech or derailleur. I wondered if I should remove the chain and see the effect of the screws without impedance by the chain, but is there an easier way?
thanks
thanks
Re: no H and L on mech screws
The two screws are there, but not marked H and L?
Jonathan
Jonathan
Re: no H and L on mech screws
yes, the screws are there, just no marks. It is a Dawes Horizon, but it is from the 80s, so I can't imagine it happens on bikes post that era!
Re: no H and L on mech screws
Thanks.
It isn't usually necessary to remove the chain to work this out.
If you change gears to the appropriate end of the travel you can then turn the screws and see which one pushes the mechanism.
And you can often do it by imagining how the bit that the screw bears on is moving as you watch while you change gear, even if you can't see it directly.
Jonathan
It isn't usually necessary to remove the chain to work this out.
If you change gears to the appropriate end of the travel you can then turn the screws and see which one pushes the mechanism.
And you can often do it by imagining how the bit that the screw bears on is moving as you watch while you change gear, even if you can't see it directly.
Jonathan
Re: no H and L on mech screws
Often with older mechs if you peer round the back you can see the inner workings: you'll see the two screws sticking down into the mechanism and a metal rocker that they make contact with. In high gear (smallest sprocket) one screw will be touching (or very nearly touching) the rocker. That's your "H" screw. Change to bottom gear (biggest sprocket) and the other screw will now be touching the rocker - that's the "L" screw. There will now be a noticeable gap between the rocker and the "H" screw.
Re: no H and L on mech screws
Like Andy says!
I can't get my head round H and L ............ they should be labelled In and Out.
As in "inner stop" and "outer stop".
I can't get my head round H and L ............ they should be labelled In and Out.
As in "inner stop" and "outer stop".
Mick F. Cornwall
Re: no H and L on mech screws
So does the In move the outer stop in or the inner stop out?
A shortcut has to be a challenge, otherwise it would just be the way. No situation is so dire that panic cannot make it worse.
There are two kinds of people in this world: those can extrapolate from incomplete data.
There are two kinds of people in this world: those can extrapolate from incomplete data.
Re: no H and L on mech screws
If you can't remember your highs and lows, then
L is for LOW
L is for LEFT
So L ajusts the left side/spoke side stop position.
Same for the front gear.
If all else fails, follow the good advice up thread of looking closely at the mech.
Unless well out of adjustment, often you only need 1/4 - 1/2 turn at a time, so do in small amounts.
L is for LOW
L is for LEFT
So L ajusts the left side/spoke side stop position.
Same for the front gear.
If all else fails, follow the good advice up thread of looking closely at the mech.
Unless well out of adjustment, often you only need 1/4 - 1/2 turn at a time, so do in small amounts.
- NATURAL ANKLING
- Posts: 13780
- Joined: 24 Oct 2012, 10:43pm
- Location: English Riviera
Re: no H and L on mech screws
Hi,
Just try and read the shimano ones that are marked on the little black plastic without your glasses L&H
I always put cable on max one way or the other then twiddle the screw.....if its right then goes stiff if not just remember to set it back where it was
Just try and read the shimano ones that are marked on the little black plastic without your glasses L&H
I always put cable on max one way or the other then twiddle the screw.....if its right then goes stiff if not just remember to set it back where it was
NA Thinks Just End 2 End Return + Bivvy - Some day Soon I hope
You'll Still Find Me At The Top Of A Hill
Please forgive the poor Grammar I blame it on my mobile and phat thinkers.
You'll Still Find Me At The Top Of A Hill
Please forgive the poor Grammar I blame it on my mobile and phat thinkers.
Re: no H and L on mech screws
What plastic?
My Shimano mech on Moulton doesn't have any plastic (other than the jockey wheels).
Second Shimano rear mech on that bike, and neither that one or this one, has any plastic.
Another thread about plastic on a front mech.
Never had a front mech with plastic on it either.
My Shimano mech on Moulton doesn't have any plastic (other than the jockey wheels).
Second Shimano rear mech on that bike, and neither that one or this one, has any plastic.
Another thread about plastic on a front mech.
Never had a front mech with plastic on it either.
Mick F. Cornwall
Re: no H and L on mech screws
Make sure there's some slack in the gear cable and undo the inner screw by one turn, If the derailleur moves inwards then you have found the L screw. If the derailleur didn't move turn the screw back to where it was, i.e. do it up one turn and then repeat the procedure with the outer screw and you should observe the derailleur move inwards, in which case this is the L screw. Logic dictates that the other screw is the H screw
Re: no H and L on mech screws
Moulton came with Tiagra front and rear.
Bought new March 2016.
Still have the same front mech.
Rear mech is now Shimano Deore XT and recently bought another as they are no longer made. The spare I have was probably the last one anywhere. Photo of it newly fitted shows it still had a sticker on it.
Bought new March 2016.
Still have the same front mech.
Rear mech is now Shimano Deore XT and recently bought another as they are no longer made. The spare I have was probably the last one anywhere. Photo of it newly fitted shows it still had a sticker on it.
Mick F. Cornwall
Re: no H and L on mech screws
To jawaka, the original poster. Is the bike a 10 or 12 speed double; if you haven't already sorted it from the instructions given above? I see from the only Dawes catalogue from the '80's with the Horizon listed that I can find - 1986; it is described as having
Suntour AR 10 speed, so 2x5 ; possibly the front derailleur is Suntour as well, I can't find an instruction leaflet for the AR, but here's one for a 1984 Suntour Cyclone which may have the same layout for the purposes of adjustment. It's just about readable.
http://www.velo-pages.com/main.php?g2_itemId=12468
The Dawes Horizon had changedto 2x6 transmission by 1990 according to the Dawes Catalogue; described as having Huret Classic 2000 sport 12 speed.
If I find any likely Huret instructions, I'll add them to this thread.
'86 Dawes Catalogue
https://dawescycles.files.wordpress.com ... es-cat.pdf
'90 Dawes Catalogue
https://dawescycles.files.wordpress.com ... at-vcc.pdf
Good Luck.
Suntour AR 10 speed, so 2x5 ; possibly the front derailleur is Suntour as well, I can't find an instruction leaflet for the AR, but here's one for a 1984 Suntour Cyclone which may have the same layout for the purposes of adjustment. It's just about readable.
http://www.velo-pages.com/main.php?g2_itemId=12468
The Dawes Horizon had changedto 2x6 transmission by 1990 according to the Dawes Catalogue; described as having Huret Classic 2000 sport 12 speed.
If I find any likely Huret instructions, I'll add them to this thread.
'86 Dawes Catalogue
https://dawescycles.files.wordpress.com ... es-cat.pdf
'90 Dawes Catalogue
https://dawescycles.files.wordpress.com ... at-vcc.pdf
Good Luck.
Nu-Fogey