Need a replacement braze-on front mech to suit 52/42/30 chainrings with 8 speed chain etc. The old mech was a Micrsoshift item - would prefer Shimano, Campag etc instead
From what I can see most modern Shimano triples are not designed for this configuration -recommendations as to what will work well gratefully received.
Ta
Front mech for 52/42/30 triple 8sp
-
- Posts: 3436
- Joined: 10 Jul 2014, 1:12pm
- Location: Norfolk
Re: Front mech for 52/42/30 triple 8sp
I'm using a Shimano Claris with a 48/38/28, which works well with 7 speed, so should be good if it is speced for a larger ring? - I think it is also available for braze on mount.
Re: Front mech for 52/42/30 triple 8sp
I've been using an Ultegra triple running off Campag levers with 52/38/26 variously with 8/9/10 speed set ups - same mech!
Whilst i prefer Campag i've found the Ultegra units to be very accomodating with extreme ranges.
Whilst i prefer Campag i've found the Ultegra units to be very accomodating with extreme ranges.
Convention? what's that then?
Airnimal Chameleon touring, Orbit Pro hack, Orbit Photon audax, Focus Mares AX tour, Peugeot Carbon sportive, Owen Blower vintage race - all running Tulio's finest!
Airnimal Chameleon touring, Orbit Pro hack, Orbit Photon audax, Focus Mares AX tour, Peugeot Carbon sportive, Owen Blower vintage race - all running Tulio's finest!
-
- Posts: 727
- Joined: 25 Aug 2014, 11:13am
- Location: South Devon
Re: Front mech for 52/42/30 triple 8sp
I too am using a Claris 8 speed, FD-2403, was 48/38/28, now 48/38/24 with 8 speed. It works fine. I'm pretty sure it's designed for 50/40/30 8 speed so it should be fine with 52/42/30. It's available as a braze-on. Presumably braze-on ones give a little adjustment? I've never used one.
Re: Front mech for 52/42/30 triple 8sp
Many thanks, but in the light of previous problems when deviating even a little from Shimano triple front mech/chainring specs, I was looking for a front mech specified to work with a 52 outer ring, 22t difference overall and 10t difference between outer and middle before parting with my cash.
I guess this is not as common a spec as maybe it once was?
I guess this is not as common a spec as maybe it once was?
Re: Front mech for 52/42/30 triple 8sp
The Claris triple is 50, 39 and 30
I think its safe to go smaller outer ring but going bigger may be risky? My Dawes 1-Down has a 46-36-26 blue RSX chainset ( intended for 3x7) and uses the front deraileur for the later black final RSX ( intended for 3x8) which was outer 50 and works fine
from an old table the Ultegra, 105SC & RX100 was 52-42-30T so maybe hunt out a good used front deraileur from those systems
useful info here
http://www.bikepro.com/
http://www.bikepro.com/products/shimano_tables/2005_tables/road_ftder05_table.html
I think its safe to go smaller outer ring but going bigger may be risky? My Dawes 1-Down has a 46-36-26 blue RSX chainset ( intended for 3x7) and uses the front deraileur for the later black final RSX ( intended for 3x8) which was outer 50 and works fine
from an old table the Ultegra, 105SC & RX100 was 52-42-30T so maybe hunt out a good used front deraileur from those systems
useful info here
http://www.bikepro.com/
http://www.bikepro.com/products/shimano_tables/2005_tables/road_ftder05_table.html
Re: Front mech for 52/42/30 triple 8sp
Many thanks for the advice, I suspect the Claris may not work well.
Sounds like a new old stock Shimano mech might be best.
Sounds like a new old stock Shimano mech might be best.
Re: Front mech for 52/42/30 triple 8sp
Using a Campag Centaur medium cage with a Veloce 53/39/30 set up off 9spd Ergos. No issues Rear wheels are either 13-26 or 12-25 depending which one has been seeing the fairy most recently... Have run 12-27 custom cassette on it too using a Marchisio 27 without issue.