eBike Conversions - Go on, show us yours!

Electrically assisted bikes, trikes, etc.
User avatar
willcee
Posts: 807
Joined: 14 Aug 2008, 11:30pm
Location: castleroe,co.derryUlster

Re: eBike Conversions - Go on, show us yours!

Postby willcee » 7 Nov 2018, 7:47pm

Ian, i understand what you say, however with 2 bafang equipped road bikes I can tell you that you don't need double rings, if you choose the correct front gearing you'll really only need perhaps 4/5 gears in normal usage.. the 250w mid bafang comes with a 46T ring, mine is now down to 42T Lekkie on the lesser powered bike and a 48 T new 110bcd with a USA made 110 convertor to hang it on the stronger one.. one is 7 sp other 8 speed. 7/8 speed is stronger cassette wise and chain wise. and i do use the gearing, but never above a 23/25 at the rear that said i have a 28 if i decide to pedal or if something happens causing power loss.. will

iandusud
Posts: 94
Joined: 26 Mar 2018, 1:35pm

Re: eBike Conversions - Go on, show us yours!

Postby iandusud » 7 Nov 2018, 8:22pm

Thanks for your input. Please bear in mind that this is for a cargo bike which might have an all up weight of 160+kg with rider and goods. With a 42t chainring I think I would have to be looking at a 10s cassette with a 42t large sprocket just to get a 1:1 bottom gear. To be honest I was hoping to go lower than that, (mtb gearing) although I appreciate that with electric assist that may not be necessary. High gears are not of interest for such a bike. An 80" top gear would be more than enough. I have other bikes for going fast - this one is for carrying loads.

Ian

kwackers
Posts: 12028
Joined: 4 Jun 2008, 9:29pm
Location: Warrington

Re: eBike Conversions - Go on, show us yours!

Postby kwackers » 7 Nov 2018, 10:04pm

iandusud wrote:I haven't discounted mid-drive as it would be the best solution for hill climbing. However there other considerations that make a powerful hub drive attractive. Advantages of a hub drive are simplicity and cost. Disadvantages of mid-drive are cost, extra wear on drive train and limited gearing, particularly low gears. I'm thinking of Bafang where you are restricted to a single chainring, with a limited choice of sizes and all sorts of chainline problems using the the larger rear sprockets as I understand it. Vulnerability of the motor as it will have to sit underneath the main horizontal spar.

Cheers,

Ian

It's all swings and roundabouts, I was simply curious because you made a big point of hills.

Couple of points.
There is more wear on the drive train without a doubt. In 10,000 miles I've gone through 3 cassettes, a chain wheel and 4 or 5 chains - although I commute throughout the winter, salt, crud and all.
(I also have a better system now which should reduce wear significantly and at some point I'm going to get rid of the derailleur and fit an IGH - better chain line, fatter chain etc.)

You can get an adaptor spider for the chainwheels which will let you use any 4/5 hole chainwheels.
Single chainwheel imo is irrelevant. I use 3 (occasionally 4) gears on my cassette which is one of the reasons they wore so fast. If you had hills you might even get more miles by virtue of using more of the cassette!

hemo
Posts: 250
Joined: 16 Nov 2017, 5:40pm
Location: West Sussex

Re: eBike Conversions - Go on, show us yours!

Postby hemo » 8 Nov 2018, 7:35pm

Woosh bikes in Southend re now selling tsdz2 48v 250w mid rive kits which are Torque sensor instead of cadence sensor similar to Bafang BBS, they will except a double front ring set up. A Bafang will but chain line is a bit out ok if you use IGH.

iandusud
Posts: 94
Joined: 26 Mar 2018, 1:35pm

Re: eBike Conversions - Go on, show us yours!

Postby iandusud » 8 Nov 2018, 8:38pm

hemo wrote:Woosh bikes in Southend re now selling tsdz2 48v 250w mid rive kits which are Torque sensor instead of cadence sensor similar to Bafang BBS, they will except a double front ring set up. A Bafang will but chain line is a bit out ok if you use IGH.


Funnily enough I just noticed that and it looks interesting. I'm still concerned about the smallest chainring it will accept and the chainline to the larger sprockets.

Cheers, Ian

hemo
Posts: 250
Joined: 16 Nov 2017, 5:40pm
Location: West Sussex

Re: eBike Conversions - Go on, show us yours!

Postby hemo » 9 Nov 2018, 9:53am

Woosh area very helpful email or phone them and they will tell you the smallest T size that will fit.

User avatar
willcee
Posts: 807
Joined: 14 Aug 2008, 11:30pm
Location: castleroe,co.derryUlster

Re: eBike Conversions - Go on, show us yours!

Postby willcee » 9 Nov 2018, 10:41pm

Yes they could approximate what size will fit.. But it depends on how the motor fits and clears the driveside of your likely wider than normal cargo bike chainstays..and thats never an exact science.. afaik it mounts same as a Bafang, on some frames they, Bafang cannot get lower than 42 unless you space at the driveside bracket, that of course has more issues with chainline especially when wanting 2 chain wheels..will

iandusud
Posts: 94
Joined: 26 Mar 2018, 1:35pm

Re: eBike Conversions - Go on, show us yours!

Postby iandusud » 10 Nov 2018, 7:25am

willcee wrote:Yes they could approximate what size will fit.. But it depends on how the motor fits and clears the driveside of your likely wider than normal cargo bike chainstays..and thats never an exact science.. afaik it mounts same as a Bafang, on some frames they, Bafang cannot get lower than 42 unless you space at the driveside bracket, that of course has more issues with chainline especially when wanting 2 chain wheels..will


Hi, Rear dropout width is 135mm (std mtb). As you suggest I don't think you can go below 42t without making the chainline even worse.

Ian

iandusud
Posts: 94
Joined: 26 Mar 2018, 1:35pm

Re: eBike Conversions - Go on, show us yours!

Postby iandusud » 10 Nov 2018, 7:26am

hemo wrote:Woosh area very helpful email or phone them and they will tell you the smallest T size that will fit.


Thanks. Once I've got the bike built and working I'll get in touch with Woosh to discuss options.

Ian

hemo
Posts: 250
Joined: 16 Nov 2017, 5:40pm
Location: West Sussex

Re: eBike Conversions - Go on, show us yours!

Postby hemo » 10 Nov 2018, 11:37pm

I use a 32 /48 double with my BBS01 and use Alfine 8 IGH, though chain line is a bit crap there is no changing issues which a derailleur would have.

iandusud
Posts: 94
Joined: 26 Mar 2018, 1:35pm

Re: eBike Conversions - Go on, show us yours!

Postby iandusud » 11 Nov 2018, 8:22am

hemo wrote:I use a 32 /48 double with my BBS01 and use Alfine 8 IGH, though chain line is a bit crap there is no changing issues which a derailleur would have.


Your comments compound my concerns about chainline issues on a derailleur set up.

Ian

Canuk
Posts: 180
Joined: 4 Oct 2016, 11:43pm

Re: eBike Conversions - Go on, show us yours!

Postby Canuk » 19 Nov 2018, 9:40pm

I can see ebike technology becoming as ubiquitous and cheap as led lightning. As soon as cheap volume, fast recharge batteries catch up with the mechanical connection its game over for LiPo, a technical solution I hate more than any other.

LiPo was always going to be a poor man's solution for bicycles. Roll on the supercapacitor battery. Its already made inroads into automotive and aerospace industries.

Its all about the batteries, folks!

kwackers
Posts: 12028
Joined: 4 Jun 2008, 9:29pm
Location: Warrington

Re: eBike Conversions - Go on, show us yours!

Postby kwackers » 20 Nov 2018, 9:38am

hemo wrote:I use a 32 /48 double with my BBS01 and use Alfine 8 IGH, though chain line is a bit crap there is no changing issues which a derailleur would have.

Any pictures?

I've an alfine 8 I'm going to use and I still haven't decided what chainwheel(s) I'll be using so I'm interested in how you've set up your double and whether the chainline is a problem because it's a double, whether it still exists with a single and if so would a 'custom' adaptor work with the BBS.