Why bolted frame, Dawes
- Patrickpioneer
- Posts: 322
- Joined: 25 Sep 2017, 11:18am
- Location: Brynteg
Why bolted frame, Dawes
Looking at the bikes on ebay, which I always do just for fun? I came across a Dawes where the rear triangle appears to be bolted, why do that and not braze it?
Re: Why bolted frame, Dawes
Good question. Some of the current Pashley range are like this too. In a quiet moment it crossed my mind that it might make them belt compatible [emoji848].
--
Cheers
Barry
Cheers
Barry
Re: Why bolted frame, Dawes
It was common on old "roadsters" so presumably that's why Pashley do it -- because they always have done. But I don't know why Dawes are doing it (unless this frame is a rebadged Chinese roadster? or just to increase their retro appeal?), nor do I know the more interesting point of why it was done originally, though I'd guess that was simply to do with practical manufacturing techniques.
Re: Why bolted frame, Dawes
One of the main reasons for bolted rear triangles is to enable a full chain guard to be fitted as on this Raleigh Superbe. Chain guards like that were once common on bikes meant for daily transport in all weathers.
'Give me my bike, a bit of sunshine - and a stop-off for a lunchtime pint - and I'm a happy man.' - Reg Baker
Re: Why bolted frame, Dawes
In the instance of raleighs, IIRC the chaincases came off without having to have bolt-in stays, indeed not all raleighs with chaincases had bolt-in stays. Nor did all bikes with bolt-in stays have chaincases, either.
If that isn't the reason for bolt-in stays, maybe they were just cheaper to make? Or maybe there was at one time a rash of brazed seatstay breakages (not that unlikely) and it was a favoured method of construction for utility bikes because it rendered the frame repairable?
I have often wondered why it was popular to do it this way, but I have yet to hear a compelling argument for it.
cheers
If that isn't the reason for bolt-in stays, maybe they were just cheaper to make? Or maybe there was at one time a rash of brazed seatstay breakages (not that unlikely) and it was a favoured method of construction for utility bikes because it rendered the frame repairable?
I have often wondered why it was popular to do it this way, but I have yet to hear a compelling argument for it.
cheers
-------------------------------------------------------------------------------
~~~~~~~~~~~~~~~~~~~~~~Brucey~~~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~~~~~~~~~~~~~Brucey~~~~~~~~~~~~~~~~~~~~~~~~
Re: Why bolted frame, Dawes
Brucey wrote:In the instance of raleighs, IIRC the chaincases came off without having to have bolt-in stays, indeed not all raleighs with chaincases had bolt-in stays. Nor did all bikes with bolt-in stays have chaincases, either.
If that isn't the reason for bolt-in stays, maybe they were just cheaper to make? Or maybe there was at one time a rash of brazed seatstay breakages (not that unlikely) and it was a favoured method of construction for utility bikes because it rendered the frame repairable?
I have often wondered why it was popular to do it this way, but I have yet to hear a compelling argument for it.
cheers
Some could be fitted without unbolting chain stays, some couldn't. I've encountered both sorts.
Not all versions of bikes with similar frames were fitted them but it must have made production easier to make all the frames in the same way.
It's also probably to do with the way chainstays were made - my 1937 Raleigh frame has the "track " style drop outs formed by pressing the chain stays almost flat and cutting the slot for the axle so bolting the seat stay meant no need for any brazing at the drop out and the top end of the seat stays are fixed using the seat clamp bolt so no brazing their either. Must have been an economical way to do things.
'Give me my bike, a bit of sunshine - and a stop-off for a lunchtime pint - and I'm a happy man.' - Reg Baker
Re: Why bolted frame, Dawes
I've wondered why too. For a short while I owned a Dutch made Union roadster with stays bolted. It was lugged and brazed at the bottom bracket but bolted at the seat cluster. I've seen a few traditional Dutch bikes made this way.
- Patrickpioneer
- Posts: 322
- Joined: 25 Sep 2017, 11:18am
- Location: Brynteg
Re: Why bolted frame, Dawes
this is the bike, look at the handlebars too,
https://www.ebay.co.uk/itm/Dawes-gents- ... 1438.l2649
https://www.ebay.co.uk/itm/Dawes-gents- ... 1438.l2649
Re: Why bolted frame, Dawes
hmm I wonder how far this could be taken to make a fully collapsable bike? that would fit into a small case?
Re: Why bolted frame, Dawes
mercalia wrote:hmm I wonder how far this could be taken to make a fully collapsable bike? that would fit into a small case?
All the way if you want - but the bike will be heavier and stiffer than it would otherwise be.
Particularly the main triangle would suffer.
A shortcut has to be a challenge, otherwise it would just be the way. No situation is so dire that panic cannot make it worse.
There are two kinds of people in this world: those can extrapolate from incomplete data.
There are two kinds of people in this world: those can extrapolate from incomplete data.
-
- Posts: 1208
- Joined: 21 Jan 2007, 3:13pm
Re: Why bolted frame, Dawes
Having looked at the e bay phot, Is that not just a bolt on gear hanger which is quite normal on ATB /Mountain Bikes these days : saves trashing the frame by breaking the fork end if you stick the mech in the back wheel.
-
- Posts: 1208
- Joined: 21 Jan 2007, 3:13pm
Re: Why bolted frame, Dawes
And have a look at Brompton/Bickerton/Dahon Folder etc etc
Re: Why bolted frame, Dawes
I wonder if it might be a bonded frame of some sort with (say) titanium main tubes and steel stays like Raleigh Dyna Tech.
It's unusual for the seat post lug to be level with the top tube like that isn't it, I noticed that the rear brake cable dives into the frame at
the lug as well which is unusual. A rack fitting on the front fork but only a mudguard eye at the rear.
It looks like the Green Dawes used on the Galaxy in the early 90's , I like a mystery!
It's unusual for the seat post lug to be level with the top tube like that isn't it, I noticed that the rear brake cable dives into the frame at
the lug as well which is unusual. A rack fitting on the front fork but only a mudguard eye at the rear.
It looks like the Green Dawes used on the Galaxy in the early 90's , I like a mystery!
Nu-Fogey
-
- Posts: 15215
- Joined: 30 Nov 2013, 11:26am
Re: Why bolted frame, Dawes
There is a lot to be said for bolting on the stays, one can repair/change them easily or convert the frame for other wheels + tyres
It must be possible to bolt the top, down and seat tubes too, I bet someone has done it already
It must be possible to bolt the top, down and seat tubes too, I bet someone has done it already
Entertainer, juvenile, curmudgeon, PoB, 30120
Cycling-of course, but it is far better on a Gillott
We love safety cameras, we hate bullies
Cycling-of course, but it is far better on a Gillott
We love safety cameras, we hate bullies
Re: Why bolted frame, Dawes
It looks like this may be a Dawes Vision with bonded aluminium frame, a picture of what looks like this very bike on page 2 of this thread
(note the bars).
http://www.retrobike.co.uk/forum/viewto ... ilit=dawes
(note the bars).
http://www.retrobike.co.uk/forum/viewto ... ilit=dawes
Nu-Fogey