Acor averhallo handlebar riser wider lower 25.4mm tubing?

[SA_SA_SA]

It occurred to me that a wider lower 25.4mm tube on the
Acor averhallo handlebar riser coukld make a useful lamp mount?

Where would one find a source of suitably strong tube,?
A 25.4mm steel ? seatpost?

[drossall]

There are lots of lamp mounts like that available anyway. For example, SJS Cycles.

[SA_SA_SA]

But I do need the acor riser as a riser as well...

[gregoryoftours]

But I do need the acor riser as a riser as well...

Google does not find the averhallo, can you post a picture of what you mean?

[SA_SA_SA]

Aberhallo

https://www.ebay.co.uk/itm/SATORI-Aberhallo-Adjust-Angle-Riser-25-4mm-Handlebar-Stem-/292185802083

[iandusud]

It occurred to me that a wider lower 25.4mm tube on the
Acor averhallo handlebar riser coukld make a useful lamp mount?

Where would one find a source of suitably strong tube,?
A 25.4mm steel ? seatpost?

Why not cut down an old set of handlebars?

[SA_SA_SA]

I didn't think the 25.4 bulge would be wide enough.

[iandusud]

I didn't think the 25.4 bulge would be wide enough.

Plenty available. It's what it's designed for.

[Jdsk]

You can buy lamp mounts that replicate bar widths, including some with holes and threads IIRC.
https://www.sjscycles.co.uk/front-light-brackets/

Jonathan

[Brucey]

25.4mm (1") OD tubing is available from any metal supplier.

cheers

[531colin]

25.4mm (1") OD tubing is available from any metal supplier.

cheers

I have found "metal mania" easy to deal with over the 'net. https://www.metalmaniauk.com/Stainless-Steel/Tube/default.aspx
They list ali and stainless tube in inch/25.4mm diameter ...any force you put through the bars will also go through this bit of tube, which won't be highly specified ;it needs to be thick enough to cope. Similarly, your existing bars will be clamped in an area they don't expect to be clamped, I don't know if this can be a problem.

[531colin]

Aberhallo

https://www.ebay.co.uk/itm/SATORI-Aberhallo-Adjust-Angle-Riser-25-4mm-Handlebar-Stem-/292185802083

Have you seen the postage?

[SA_SA_SA]

I didn't think the 25.4 bulge would be wide enough.

Plenty available. It's what it's designed for.

I meant the bulge needs to be wider than I have seen on handlebars in order to suit the wider lower part of the aberhallo.

Aberhallo

https://www.ebay.co.uk/itm/SATORI-Aberhallo-Adjust-Angle-Riser-25-4mm-Handlebar-Stem-/292185802083

Have you seen the postage?

I already have one so no, I just picked that link for the photo.

25.4mm (1") OD tubing is available from any metal supplier.

cheers

I have found "metal mania" easy to deal with over the 'net. https://www.metalmaniauk.com/Stainless-Steel/Tube/default.aspx
They list ali and stainless tube in inch/25.4mm diameter ...any force you put through the bars will also go through this bit of tube, which won't be highly specified ;it needs to be thick enough to cope. Similarly, your existing bars will be clamped in an area they don't expect to be clamped, I don't know if this can be a problem.

Thanks, but⁸
I have managed to fit the lamps to the handlebars using brackets that I had in spares box

[iandusud]

These would do the trick.
https://www.ebay.co.uk/itm/UK-Road-Bike ... SwQJlf7URA
As others have said 25.4 tube is readily available. I have the same Satori riser for our tandem so know that our stockers bars have a wide enough bulge. Of course not all bars will.